Latest Cisco 300-080 Exam Questions For Free – (Jan-2018 dumps)

Passing Cisco Certified Network Professional Collaboration 300-080 exam with overnight preparation is not hard if you get both practice test software and PDF files preparation products with money back guarantee. Troubleshooting Cisco IP Telephony and Video 300-080 exam Practice test software is a simulation like real 300-080 exam however PDF files provide the latest 300-080 exam questions very similar to the pattern of real 300-080 exam questions. Make MacAfee Secure transaction to get these 300-080 exam questions with money back guarantee.

♥♥ 2018 NEW RECOMMEND 300-080 Exam Questions ♥♥

300-080 exam questions, 300-080 PDF dumps; 300-080 exam dumps:: https://www.dumpsschool.com/300-080-exam-dumps.html (157 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 300-080 Dumps Exam Questions and Answers:

Version: 10.0
Question: 21

When parsing trace output after the call routing decision and path selection have been made, which two records can be found in the CCM|RouteList? (Choose two.)

A. PretransfromDigitString
B. CallingPartyNumber
C. PretransformCallingPartyNumber
D. RouteListName
E. findLocalDevice
F. RouteListCdrc :

Answer: D, F

Question: 22

Refer to the exhibit.

The exhibit shows the output of debug isdn q931. An inbound PSTN call was received by a SIP gateway that is reachable via a SIP trunk that is configured in Cisco Unified Communications Manager. The call failed to ring extension 3001. If the phone at extension 3001 is registered and reachable through the gateway inbound CSS, which three actions can resolve this issue? (Choose three.)

A. Change the significant digits for inbound calls to 4 on the SIP trunk configuration in Cisco Unified Communications Manager.
B. Configure the digit strip 4 on the SIP trunk under Incoming Called Party Settings in Cisco Unified Communications Manager.
C. Configure a translation pattern in Cisco Unified Communications Manager that can be accessed by the trunk CSS to truncate the called number to four digits.
D. Configure a called-party transformation CSS on the gateway in Cisco Unified Communications Manager that includes a pattern that transforms the number from ten digits to four digits.
E. Configure a voice translation profile in the SIP Cisco IOS gateway with a voice translation rule that truncates the number from ten digits to four digits.
F. Configure the Cisco IOS command num-exp 2288223001 3001 on the gateway ISDN interface.

Answer: A, C, E

Question: 23

You configured a Cisco ISR G2 as a SIP gateway, but the gateway does not show that it is registered with Cisco Unified Communications Manager. What is causing this issue?

A. Cisco Unified Communications Manager does not support SIP gateways.
B. The gateway does not have the UC license installed.
C. The gateway does not have Cisco Unified Border Element session licensing.
D. Cisco Unified Communications Manager does not show a SIP gateway as registered if it is not properly configured.
E. Cisco Unified Communications Manager never shows a SIP gateway as registered even when it is properly configured.
F. The Cisco ISR G2 cannot be a SIP gateway.

Answer: E

Question: 24

Which issue would cause an MGCP gateway to fail to register with Cisco Unified Communications Manager?

A. missing the configuration command isdn bind-l3 ccm-manager under the ISDN interface
B. mismatched domain name on the MGCP gateway and Cisco Unified Communications Manager gateway configuration
C. misconfigured route group in Cisco Unified Communications Manager
D. incorrect MGCP IP address specified in the gateway configuration in Cisco Unified Communications Manager

Answer: B

Question: 25

Endpoints are configured for both H.323 and SIP using the same URI and Cisco VCS settings, but the endpoints register only as H.323 endpoints. What is causing this issue?

A. A firewall is blocking all traffic from the endpoints to the Cisco VCS.
B. The Cisco VCS has no SIP domains configured.
C. The Cisco VCS is blocking the endpoints because of duplicate ID entries.
D. The endpoints do not have the SIP option key installed.
E. SIP does not work, because SIP is used for Cisco Unified Communications Manager registration only.

Answer: B

Question: 26

You are trying to register an H.323-based Cisco TelePresence system to Cisco Unified Communications Manager and a Cisco DX70 system to the Cisco VCS Control. Why do neither of the units want to register?

A. The H.323-based system needs an E164 number to register to Cisco Unified Communications Manager, and the Cisco DX70 needs to have the MAC address configured first on the Cisco VCS Control.
B. The H.323-based system needs to register to the Cisco VCS Control with an E.164 number, and the Cisco DX70 needs the TFTP address to register on the Cisco Unified Communications Manager.
C. Both systems need to register to the Cisco VCS Control, but the H.323-based system needs to have the gatekeeper setting set to “Direct.”
D. Both systems need to register to the Cisco Unified Communications Manager, as the Cisco VCS Control is used only for firewall traversal.
E. You need Cisco TelePresence Management Suite to register Cisco TelePresence systems.
F. You need Cisco TelePresence Server to register Cisco TelePresence systems.

Answer: B

New Updated 300-080 Exam Questions 300-080 PDF dumps 300-080 practice exam dumps: https://www.dumpsschool.com/300-080-exam-dumps.html

         

Facebook Comments